[slab42]

I know I just did the DIY fender eliminator, but I did not like the fact that I did not have a plate light. I decided to buy the R & R fender eliminator and the license plate bar from SPR engineering. I got the R & R because I did not want the wires for the light bar up against the exhaust, and this way it is zip tied to the FE, and looks real clean. I even put a strip of red reflective tape on the plate to keep her legal. Both products I can say are well built. Very nice stuff.

 

[600rrrider]

How much did the plate light set you back?

 

[risky_analyst]

nice 5 series.. i especially like the drink fridge in the garage.

 

[slab42]

the plate light was 43 bucks shipped
thanks for the compliment on the car, it's my dad's baby, and the drink fridge comes in handy! no need to leave the garage!

 

[SPR SLO]

I have to say I am really impressed not only with the build quality, but the brightness of my SPR engineering plate lights also. Much better than the lite'n'boltz junk I had before.

 

[tribals-10]

The only problem with the drink fridge is if you leave any bud light in it his mother will drink it. And by the looks of those pics there's only one bud light left!

 

[Lan]

I know I just did the DIY fender eliminator, but I did not like the fact that I did not have a plate light. I decided to buy the R & R fender eliminator and the license plate bar from SPR engineering. I got the R & R because I did not want the wires for the light bar up against the exhaust, and this way it is zip tied to the FE, and looks real clean. I even put a strip of red reflective tape on the plate to keep her legal. Both products I can say are well built. Very nice stuff.

Looks good man. What Beamer you got?

 

[DhoomRR]

Yeah that looks sweet...always liked that plate light. I don't ride at night at all so haven't really had to worry about having a plate light....for now at least.

 

[slab42]

the beamer is pops' 530i.

 

[CBR/LS1]

I like that plate light looks realy good.

 

[larry]

Looking good!

 

[rendizzo]

Looks like someone is addicted to Diet Pepsi...

SWEET FE too. Like those lights. Might have to bite yo style. Got a link?

 

[slab42]

the lights are on http://www.sprengineering.com/platelights/index.html (scroll to the bottom)
the FE I got from ebay (seller name is randrcycles)

 

[rendizzo]

sweet. Thanks bro.

 

[LilGuns]

That Is A Great Set Up Wish I Had Done More Research Before I Got Mine For 100$. What A Waste!

 

[teg]

i ordered the R&R fender eliminator too but it havent arrive yet, i see that you still have the stock turn signal, is it necessary for installation ? or can i just leave out the stock signal since i ordered integrated taillight as well

 

[slab42]

I used the factory reflector brackets and drilled them out to fit the factory signals. you do not need to retain them. i just chose to use them instead of aftermarket ones.

 

[silvrr600]

Ok I did the FE on mine with the signals in the reflectors yada yada yada and I went riding tonight checked everything and noticed the rear signals dont run all the time like the fronts....Is this normal or did I mess something up? I didnt change wiring at all so I dont see how I could of. Just wanted to know before anything else possibly goes down

 

[Mick]

Ok I did the FE on mine with the signals in the reflectors yada yada yada and I went riding tonight checked everything and noticed the rear signals dont run all the time like the fronts....Is this normal or did I mess something up? I didnt change wiring at all so I dont see how I could of. Just wanted to know before anything else possibly goes down

Yes that is normal, the rear signals do not run all the time, only when they are activated by the switch.

 

[aggieRR]

hey slab, i have the same plate light and i contemplated putting it somewhere near where yours is, do you notice any negative things from it being so close to the can?