Honda CBR 600RR Forum banner

1 - 20 of 97 Posts

·
Registered
Joined
·
132 Posts
Discussion Starter #1
Ok so after a few pms Ive realized not everyone has the means to make a marking bolt themselves. I made one and no longer need it. Is what I would like to to is share it for everyone. I'm going to pay it forward to anyone that needs it. All I ask is when you are done either mail it back to me or to the next person who signs up in this thread. I like priority usps. Shouldnt be more than 4-5 bucks anywhere in the US.



1.
2.
3.
4.
 

·
Registered
Joined
·
619 Posts
2. Naughty
3.
4.
 

·
Registered
Joined
·
132 Posts
Discussion Starter #8
Ok sent out the bolt this morning. For everyone doing the install 1 7/8 hole saw and a rounded rasp make this job so much easier.
 

·
Registered
Joined
·
12 Posts
Fearing cuts?

Alright.... I put frame sliders on my 09' but in order for me to put the fearings back on I need to cut it in order for the fearings to fit. Does anyone know if you can do it your self with out cracking or damageing the fearings?
 

·
*BOTM Feb '11, Mar '12*
Joined
·
23,598 Posts
Alright.... I put frame sliders on my 09' but in order for me to put the fearings back on I need to cut it in order for the fearings to fit. Does anyone know if you can do it your self with out cracking or damageing the fearings?
Try putting the newly cut fairing back on w/o the frame slider. Then make any additional cuts or adjustments when test fitting the frame slider back on with the fairing in place
 

·
Registered
Joined
·
132 Posts
Discussion Starter #11 (Edited)
Alright.... I put frame sliders on my 09' but in order for me to put the fearings back on I need to cut it in order for the fearings to fit. Does anyone know if you can do it your self with out cracking or damageing the fearings?
If im understanding this, and I like to think that I am, you havent cut the fairings yet. Thats what the marking bolt is for. You screw this in where the frame sliders would go and slap your plastic back on without bolts. Have a buddy stand on the other side of your bike and push really hard in the general area of the bolt and it will put a nice indention in the plastic. Drill yourself a pilot hole, whipout your favorite hole saw, and your in like Flynn.
 

·
Registered
Joined
·
282 Posts
I do wanna use it, but how long will it be to get to me?

1. hyper cbr PENDING
2. Naughty
3. Winiferd
4. dses91
5. yummee
6.
 

·
Registered
Joined
·
132 Posts
Discussion Starter #17
update: Im going to carve up my factory bolts when I get off work. That will give us 3 marking bolts. I will contact the next two on the list. I use priority usps, all I ask is a small paypal payment to cover shipping. It was 4.85 to NJ from KY for reference.
 

·
Registered
Joined
·
619 Posts
well hyper and I both live in NJ. So im sure he can prolly mail it to me very cheap. and thanx again man. saving us all money and hassle.
 

·
Virgin Stud
Joined
·
48 Posts
Gf8coupe I would like to say that this type of thread/help is just what makes 600rr.net so great. You are a great contribution to this site and even though I don't need this tool because I already had mine done at the shop I would just like to say thank you. If you need any help please feel free to PM me anytime. I take joy in helping those who help others. Have a good one!
 

·
Registered
Joined
·
132 Posts
Discussion Starter #20
OK so I worked over a factory bolt tonight, and they are just too short. Im going to go buy the bolt store in the AM and just buy some. My fiance's bachorlette party is tomorrow night and I have to vacate the house. I'll have a couple new bolts ready to ship out Saturday sometime.
 
1 - 20 of 97 Posts
Top